Quick answer
- Find your full model code on the rating label and open the matching instruction manual.
- Setting up for the first time? Check the model’s standing time, fit the tank and use the panel diagram to choose a mode.
- Tank light or error code? Note what the display says and check the instructions for your model.
Looking for Pro Breeze dehumidifier instructions? Start with the model code on your appliance. Find the right PDF below, then use the setup, tank, drainage and cleaning sections to get back to what you were doing.
1Find your Pro Breeze dehumidifier manual
Look for Model on the rating label, usually on the back or side of the appliance. Copy the full code, including letters such as WF and any regional suffix. Keep the serial number for support, if asked. If you have a refurbished unit, match the label on the unit itself.
A capacity such as 12L or 20L describes how much moisture a model is rated to remove per day under stated conditions. Several appliances can share that capacity and have different controls. Match the label to the table, then use the PDF link to open the first page of the English instructions. Where a manual uses a shorter code on the cover, look for the full regional code in its specifications.
12L and 20L dehumidifier manuals
| Model | Manual or label code | Instructions |
|---|---|---|
| OmniDry 12L Quiet | PB-18 / PB-D-18 | Download PDF Standard controls and error-code table. English starts on PDF page 2. |
| OmniDry 12L Quiet, black | Check the full code on the label | Request the EU manual Send the full code so we can match the control panel. |
| OmniDry 12L Quiet with app | PB-D-18W-WF | Download PDF Wi-Fi pairing and controls. English starts on PDF page 4. |
| 12L with built-in humidistat | PB-06 | Download PDF Use this version for a label that reads PB-06. English starts on PDF page 3. |
| 12L with humidistat and app | PB-D-06W-W-EU | Request the EU manual Ask for the app-enabled manual and pairing steps. |
| 12L Compact | PB-D-27 | Download PDF Assembly, controls and gravity drain. English starts on PDF page 3. |
| OmniDry 20L with app | PB-D-24-WF | Download PDF Wi-Fi, Auto, Laundry and Night modes. English starts on PDF page 4. |
| OmniDry 20L without app | PB-D-24W-EU | Download PDF · View manual Panel controls and gravity drain. English starts on PDF page 4. |
| 20L Max Extraction with Laundry Mode | PB-08 | Download PDF Use this version for a label that reads PB-08. English starts on PDF page 3. |
| 20L Max Extraction with app | PB-D-08W-W-EU | Request the EU manual Ask for the app-enabled manual and pairing steps. |
| 20L Premium One-Click Laundry | PB-D-23 | Download PDF Dedicated laundry setting and removable filters. English starts on PDF page 4. |
| 20L Premium One-Click Laundry with app | PB-D-23W-W | Download PDF Smart app instructions and filter care. English starts on PDF page 4. |
Mini, compact, desiccant and high-capacity manuals
| Model | Manual or label code | Instructions |
|---|---|---|
| 500 ml Mini | PB-02 | Download PDF Power switch and tank-full indicator. English starts on PDF page 2. |
| 1000 ml Mini with timer and LED light | PB-17 family | Download PDF Pan-European booklet. Match the code and controls on your unit, including colour variants. English starts on PDF page 2. |
| 1500 ml Mini | PB-03 | Download PDF On/off control and tank removal. English starts on PDF page 2. |
| 1500 ml Premium Mini | PB-13 | Download PDF Check the label, since two mini models have this tank size. English starts on PDF page 3. |
| 6L Compact | PB-D-26 | Download PDF Assembly, controls and gravity drain. English starts on PDF page 2. |
| OmniDry 10L | PB-D-40W | Download PDF The manual lists the EU and RT-EU versions. English starts on PDF page 4. |
| 10L Desiccant with Heating Function | PB-10 | Download PDF Use the desiccant controls and drainage instructions. English starts on PDF page 2. |
| 25L High Capacity with 6.5L Tank | PB-D-30 family | Request the EU manual Send the regional model suffix to get the right edition. |
| 25L Max Extraction with Smart App | PB-D-37W-W | Download PDF Match the full model code before using the app and tank instructions. English starts on PDF page 4. |
| AeraDry® 25L 2-in-1 | PB-D-33W-K-EU | Request the EU manual Ask for the combined dehumidifier and purifier manual. |
| 30L with Smart App Control | PB-15 | Download PDF Match the PB-15 label, as the 30L range uses different panels. English starts on PDF page 3. |
| 30L Max Extraction with Smart App | PB-20 | Download PDF Match the PB-20 label before following the setup steps. English starts on PDF page 2. |
| OmniDry 40L with app | PB-D-32W-W | Download PDF Smart controls, continuous drainage and code table. English starts on PDF page 3. |
If you need help finding a match, use the request link and send a clear photo of the rating label and the control panel. If the PDF opens at the cover, go to the page listed above for the English instructions. To compare models before you buy, use the 13-step dehumidifier buying guide.
2Set up your dehumidifier for the first time
- Read the setup and safety pages in your manual. Check the standing time after transport for your model before plugging it in. Keep the unit upright as you move and position it.
- Place the unit on a level, dry surface. Follow the placement and room requirements in the manual. Make sure packing materials are clear of the air inlet and outlet. Fit any separate parts, such as wheels, only as shown in the assembly section.
- Seat the water tank fully. Slide it into place in the direction shown in the manual. Use the supplied adaptor on a mini model or the connection specified on the rating label for other units.
- Switch on and choose a mode. Use Auto where provided for an ordinary first run. The controls section of your PDF shows how to tell the room reading from your chosen setting. On a mini, look for the power and full-tank lights.
If the unit powers on but collects very little water, check that the current room reading is above the target in Auto mode, that the temperature is within the manual’s operating range and that the tank is seated. A brief pause can be part of defrosting on a compressor model. Check its display before changing the settings.
3Use the controls on your model
On OmniDry 12L PB-18, use the manual’s panel diagram to tell the humidity reading, target setting and timer apart. The PB-D-18W-WF has its own panel diagram and app setup section. Follow that section when pairing the smart model.
On OmniDry 20L PB-D-24-WF, press Mode to choose Auto or Laundry. Hold Mode to switch Night mode on or off. Auto responds to the target humidity. Laundry runs continuous extraction. Night mode dims the display. The app section explains the Wi-Fi indicator. On the PB-D-24W-EU, use the panel instructions in its own PDF.
The PB-D-23 Premium 20L has a dedicated laundry button. The 500 ml mini has a power switch and tank indicator. For the 1 L mini, check its own guide for the timer. These controls serve different jobs, so start with the panel diagram for your model. For room and load examples, read how to dry laundry with a dehumidifier.
4Empty the tank or fit the drain hose
For tank collection, switch the unit off and follow the manual’s removal steps. Hold the tank level as you slide it out, empty it into a suitable drain, then reseat it. If the tank-full light stays on with an empty tank, check that the tank is seated and follow the troubleshooting steps for your label code.
For models with gravity drainage, switch off and unplug the appliance before setting up the hose. Find the outlet in your PDF. Some models give access behind the tank. Fit the hose as shown, refit the tank if the manual calls for it, and route the hose down to a suitable drain. Secure the end and keep the hose clear of kinks. If the water still goes into the tank or backs up, switch off and check the connection, slope and outlet position against the manual. Mini models with tank collection use the emptying procedure instead.
5Find an error code or indicator
Write down the whole code before switching modes. On the OmniDry 20L PB-D-24-WF, FL is the full-tank indication. Empty and reseat the tank using the manual steps. On that model, E0 is a wiring fault and E1/E2 relates to humidity sensing. The manual directs you to Pro Breeze Customer Care. The OmniDry 12L PB-18 lists E0 for wiring and E2 for the humidity sensor. Use that model’s code table for LO, HI, CL or CH.
A mini can indicate a full tank with a light. Check the light colour and what it means in your own manual. If the display or indicator does not match the code table, or an error persists after the listed owner checks, contact Pro Breeze with the label code, displayed code and a photo. Leave internal repair to qualified service.
6Clean the filter and water tank
Switch off, unplug and empty the tank before cleaning. Wipe the case gently and use the tank cleaning instructions in your model’s PDF. Dry the parts that the manual tells you to dry before refitting. Check how to reach the filter first, since access differs between models.
For example, the OmniDry 20L PB-D-24-WF manual specifies a brush attachment on a vacuum for dust on the rear air filter and a two-week cleaning interval. Other filters have their own instructions. With a combined purifier such as AeraDry®, identify the dust filter and HEPA cartridge separately and use the care instructions for each. Before storage, empty and dry the tank as directed in the manual.
7Frequently asked questions
Can I use the same instructions for every 12L or 20L dehumidifier?
Match the label code in the directory. For example, an OmniDry 20L PB-D-24-WF has app setup instructions, and PB-D-24W-EU has its own controls. The OmniDry range guide explains the differences between sizes.
Why did the dehumidifier stop when the tank still had space?
Check the display and the operating mode. Auto can pause extraction when it reaches the target. A compressor model can also pause during automatic defrost. If it shows a full-tank light or a code, follow the relevant manual steps.
How much does a session cost?
Multiply rated power in kilowatts by hours and the rate on your bill. At the EU example rate of €0.28 per kWh, one hour at the OmniDry 12L’s rated 200 W is about €0.06. Actual use depends on settings and how long the compressor runs. See the dehumidifier running costs guide for more examples.
OmniDry 10L Quiet Compact Space Saving Low Energy Dehumidifier with Laundry Mode
€89,99
€119,99
OmniDry 40L Quiet Low Energy Dehumidifier with Laundry Mode and Smart App Control
€219,99
€269,99
Comparing models or looking for a product page? Explore the Pro Breeze home dehumidifier range for product details.






